rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs2-s10m/d10m 1.0w semi-regulated single & dual output we energize electronics! an acal group company we energize electronics! features ? 7 pin sil package ? 1000vdc isolaton ? up to 3000vdc isolaton ? low ripple and noise ? efciency up to 89% ? operatng temperature range: -40 ~ +85c ? non conductve black plastc case ? emi complies with en55022 class b output specification voltage accuracy: 3% line regulaton: per 1%vin change: 1.2% load regulation: from 10% to 100% load: see table ripple & noise: 50mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: 10% max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20-50ma pk-pk by 5v-48v general specifications efciency: see table i/o isolaton voltage (60sec): 1000 ~ 3000vdc i/o isolaton capacitance: 60pf typ. i/o isolaton resistance: 1000m ohm switching frequency: variable 70khz humidity: 95% rel h reliability calculated mtbf : >2.0mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: non-conductve black plastc (ul94v-0 rated) pin material: c5191r-h solder coated potng material: epoxy (ul94v-0 rated) weight case- sip: 2.4 ~ 2.8g dimmension sip: 0.76 x 0.24 (28) x 0.39 absolute maximum ratings (1) input surge voltage (100ms)/ 5 v models: 9vdc max 12v models: 18vdc max 15v models: 20vdc max 24v models: 30vdc max 48v models: 54vdc max soldering temperature (2) : 260c max. emc specifications radiated-/conducted emissions: en55022 class b esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 dc/dc-converter rs2-s10m/d10m 1.0w semi-regulated single & dual output we energize electronics! an acal group company we energize electronics! model selection guide model number input voltage range (vdc) input current output voltage (vdc) output current full load (ma) load regulation % efficiency @fl(%) capacitor load(uf) no - load (ma) full load (ma) rs2 - 0505 d10 ax m 5 20 2 3 0 5 100 6 84 100 rs2 - 0509 d10 ax m 5 30 2 3 0 9 55.55 5.5 86 100 rs2 - 0512 d10 ax m 5 20 2 2 8 12 41.67 5.5 87 47 rs2 - 0515 d10 ax m 5 20 2 2 8 15 33.33 5 87 47 rs2 - 1205 d10 ax m 12 15 9 8 5 100 4 85 100 rs2 - 1209 d10 ax m 12 15 9 5 9 55.55 3.5 86 100 rs2 - 1212 d10 ax m 12 15 9 4 12 41.67 3.5 87 47 rs2 - 1215 d10 ax m 12 15 9 4 15 33.33 3.5 87 47 rs2 - 1505 d10 ax m 15 10 7 8 5 100 3.5 85 100 rs2 - 1509 d10 ax m 15 10 7 6 9 55.55 2.5 87 100 rs2 - 1512 d10 ax m 15 10 7 6 12 41.67 2.5 87 47 rs2 - 1515 d10 ax m 15 10 7 5 15 33.33 2.5 88 47 rs2 - 2405 d10 ax m 24 7 5 1 5 100 3.5 82 100 rs2 - 2409 d10 ax m 24 7 4 9 9 55.55 2.5 85 100 rs2 - 2412 d10 ax m 24 7 4 8 12 41.67 2.5 87 47 rs2 - 2415 d10 ax m 24 7 4 8 15 33.33 2.5 87 47 rs2 - 4805 d10 ax m 48 5 2 7 5 100 3 77 100 rs2 - 4809 d10 ax m 48 5 2 6 9 55.55 3 81 100 rs2 - 4812 d10 ax m 48 5 2 6 12 41.67 3 82 47 rs2 - 4815 d10 ax m 48 5 2 6 15 33.33 2 81 47 rs2 - 0505 s10 ax m 5 20 2 5 0 5 200 6 83 220 rs2 - 0509 s10 ax m 5 20 2 3 0 9 111.1 5.5 86 220 rs2 - 0512 s10 ax m 5 20 2 3 0 1 2 83.3 5.5 87 100 rs2 - 0515 s10 ax m 5 20 2 3 0 1 5 66.7 5 87 100 rs2 - 1205 s10 ax m 12 15 9 8 5 200 4 84 220 rs2 - 1209 s10 ax m 12 15 9 6 9 111.1 3.5 86 220 rs2 - 1212 s10 ax m 12 15 9 5 1 2 83.3 3.5 88 100 rs2 - 1215 s10 ax m 12 15 9 5 1 5 66.7 3 88 100 rs2 - 1505 s10 ax m 15 10 7 9 5 200 4 84 220 rs2 - 1509 s10 ax m 15 10 7 7 9 111.1 3.5 86 220 rs2 - 1512 s10 ax m 15 10 7 6 1 2 83.3 3.5 87 100 rs2 - 1515 s10 ax m 15 10 7 6 1 5 66.7 3 89 100 rs2 - 2405 s10 ax m 24 7 5 1 5 200 4 81 220 rs2 - 2409 s10 ax m 24 7 5 0 9 111.1 3.5 84 220 rs2 - 2412 s10 ax m 24 7 4 9 1 2 83.3 3.5 85 100 rs2 - 2415 s10 ax m 24 7 4 9 1 5 66.7 2.5 86 100 rs2 - 4805 s10 ax m 48 5 2 7 5 200 4 78 220 rs2 - 4809 s10 ax m 48 5 2 6 9 111.1 3.5 80 220 rs2 - 4812 s10 ax m 48 5 2 6 1 2 83.3 3 81 100 rs2 - 4815 s10 ax m 48 5 2 6 1 5 66.7 3 81 100 suffix ? 3 ? means 3 k vdc isolation type m = semi regulated the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e - mail t o : info@ rsg - electronic.de r s2 - xx xx x xx power ( w) input t ype a x m code inter nal isolation (kvdc) 10=1.00 20=2.00 r s2 - xx xx x xx power ( w) input t ype a x m code inter nal isolation (kvdc)
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 output ripple & noise measurement test the scope measurement bandwidth is 0 - 20mhz. emi filter input filter components (c1, l,c2,c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. load c3 c1 l c2 c3 rs2 - 05 x x s/d10a x m 1210, 2.2uf/100v 18uh rs2 - 12x xs/d10ax m 1210, 2.2uf/100v 18uh rs2 - 15xx s/d10ax m 1210, 2.2uf/100v 1 8 u h rs2 - 24xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs2 - 48xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv vu v dc/dc c - v - vu l l c 1 c 2 vu dc/dc c - vu sp 1. rpp/ u 20mh . 2. v u . 3. pu p c1, l,c2, c3 u p u u u. p u u p u u . 4. a p u u c61000 - 4 - 4 p rs u pp - k , 220uf/100v. 5. u u u u . uu p. 6. p u - , p. output ripple & noise measurement test the scope measurement bandwidth is 0 - 20mhz. emi filter input filter components (c1, l,c2,c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. load c3 c1 l c2 c3 rs2 - 05 x x s/d10a x m 1210, 2.2uf/100v 18uh rs2 - 12x xs/d10ax m 1210, 2.2uf/100v 18uh rs2 - 15xx s/d10ax m 1210, 2.2uf/100v 1 8 u h rs2 - 24xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs2 - 48xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv +vout +v in dc/dc converter - vin - vout l load c 1 c 2 +vout dc/dc converter - vout sp 1. rpp/ u 20mh . 2. v u . 3. pu p c1, l,c2, c3 u p u u u. p u u p u u . 4. a p u u c61000 - 4 - 4 p rs u pp - k , 220uf/100v. 5. u u u u . uu p. 6. p u - , p. dc/dc-converter rs2-s10m/d10m 1.0w semi-regulated single & dual output we energize electronics! an acal group company we energize electronics! output ripple & noise measurement test the scope measurement bandwidth is 0 - 20mhz. emi filter input filter components (c1, l,c2,c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. load c3 c1 l c2 c3 rs2 - 05 x x s/d10a x m 1210, 2.2uf/100v 18uh rs2 - 12x xs/d10ax m 1210, 2.2uf/100v 18uh rs2 - 15xx s/d10ax m 1210, 2.2uf/100v 1 8 u h rs2 - 24xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs2 - 48xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv +vout +v in dc/dc converter - vin - vout l load c 1 c 2 +vout dc/dc converter - vout sp 1. rpp/ u 20mh . 2. v u . 3. pu p c1, l,c2, c3 u p u u u. p u u p u u . 4. a p u u c61000 - 4 - 4 p rs u pp - k , 220uf/100v. 5. u u u u . uu p. 6. p u - , p. output ripple & noise measurement test the scope measurement bandwidth is 0 - 20mhz. emi filter input filter components (c1, l,c2,c3) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. load c3 c1 l c2 c3 rs2 - 05 x x s/d10a x m 1210, 2.2uf/100v 18uh rs2 - 12x xs/d10ax m 1210, 2.2uf/100v 18uh rs2 - 15xx s/d10ax m 1210, 2.2uf/100v 1 8 u h rs2 - 24xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv rs2 - 48xxs/d10ax m 1210, 2.2uf/100v 1 8 u h 1210, 2.2uf/100v 1206, 470pf/2kv +vout +v in dc/dc converter - vin - vout l load c 1 c 2 +vout dc/dc converter - vout sp 1. rpp/ u 20mh . 2. v u . 3. pu p c1, l,c2, c3 u p u u u. p u u p u u . 4. a p u u c61000 - 4 - 4 p rs u pp - k , 220uf/100v. 5. u u u u . uu p. 6. p u - , p.
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 rs2-xxxxs10a1m rs2-xxxxs10a1m dc/dc-converter rs2-s10m/d10m 1.0w semi-regulated single & dual output we energize electronics! an acal group company we energize electronics! the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
